- 上海乾拓貿易有限公司 >>> 技術文獻
HERION電磁閥運轉中的問題資料有哪些？
般都是選型問題，者介質的屬性出現了變化，導致HERION電磁閥部件及閥芯等，不能正常工作。用戶可以重新確認電磁閥介質屬性，或者配備合適的電磁閥型號產品。
HERION電磁閥閥芯損壞
般造成HERION電磁閥閥芯損壞的原因比如使用的介質屬性和環境超過工作范圍，或者電磁閥使用時間過長、操作不當而導致的。造成電磁閥芯故障的原因有很多，多是因?yàn)殚L期的使用，超過了使用年限，壽命到期，或者因?yàn)椴僮骱褪褂貌徽?dāng)造成的非正常損壞。正確的閥芯故障檢測方法是檢測是否是使用壽命到期，其次是介質的屬性和環境有沒有在高壓蒸汽電磁閥產品的工作范圍里面，zui后是檢測有沒有堵塞的情況。
HERION電磁閥在使用的過程中，應注意該的壓力工作范圍，超過工作范圍的工作壓力會損壞電磁閥，造成泄漏以及給用戶帶來損失。如果有壓力異?；虺^電磁閥的實際工作范圍，請立即關閉電磁閥的前后手動閥，停止電磁閥的工作。
HERION電磁閥的密封是整個電磁閥的重要部件之，應確保電磁閥密封的。并保持電磁閥密封內部的清潔。
由于HERION電磁閥系列的型號多樣，每個型號都有自己的特性和工作范圍。對于新用戶來說，可以參考廈門乾球自動化銷售人員和技術人員的介紹，選擇更合適您的。
機械設備在工作的狀態下，應避免松動的情況發生，以減少機械振動，降低機械損壞，延長電磁閥使用壽命。
對于工作在特殊環境的電磁閥，例如接近水源，工作環境雜物過多等，應為電磁閥配備合適的防護設備。電磁閥的使用壽命，在用戶方面的維護和使用操作也會造成定的影響。而選擇合適的電磁閥型號也很重要，用戶們在購買力典電磁閥的時候，請盡量提供詳細的要求和工作條件，介質屬性等，這樣才可以選擇更加合適用戶的電磁閥。
以下是參考譯文：
1, solenoid valve coil burned out, can remove the solenoid valve wiring, measured with a multimeter, if open, the solenoid valve coil burned. Moisture causes the coil, magnetic flux leakage caused by bad insulation, causing the coil current is too large to burn. Countermeasures: so to prevent flood water from entering the solenoid valve. In addition, excellent spring, reaction force is too large, too few coil turns, the suction can not make the coil burnt. Emergency treatment, can be "0" bit hit "1" bit manual button on the coil from the normal work, makes the valve open. 2, solenoid valve head loose or thread off wiring, electric solenoid valve shall be fastened thread:, countermeasures. 3, solenoid valve stuck. Slide valve sleeve and spool valve clearance Anhui SECCO environmental protection science and technology supply is very small (less than 0.008mm), are generally single assembly, when a mechanical impurities into or too little lubricant, it is easy to get stuck. Countermeasures: can hold into the wire hole from the head to make it bounce. The fundamental solution is to remove the valve, remove the spool and spool cover, clean with CCI4, making flexible movement in the valve spool sleeve. Demolition should pay attention to the assembly sequence and location of the external connection of each component, in order to re assembly and wiring is correct, also check whether the plug hole injector lubricator, lubricating oil is sufficient. 4, leakage. Lack of air pressure can cause leakage, making enforcement difficult to open and close the valve, the reason is the slide valve gasket damage or wear caused by several cavity channeling gas. Countermeasures: in dealing with the electromagnetic valve failure switching system, should select the appropriate time, such as the solenoid valve is energized when dealing with, if not processed in a gap switch, switching system can be suspended, disposed of
